Yes. Reverse osmosis removes both forms of arsenic from drinking water, and it is one of the few home technologies that does so reliably. Removal rates run from roughly 90 to 99 percent, depending on the arsenic species, membrane, water chemistry, and system design. The practical catch is that removal is not automatic. A poorly maintained or undersized system can pass arsenic, and the waste stream concentrates it.
The separation mechanism
Reverse osmosis works by pressure, not by capture. A pump pushes feedwater against a semipermeable membrane at pressures well above the water's natural osmotic pressure. Water molecules cross the dense polyamide layer; dissolved ions and small molecules are left behind and swept away in a concentrate stream.
Arsenic rejection depends on charge and size. Arsenate, the oxidized form (As(V)), behaves like a divalent anion at normal drinking-water pH. The membrane's fixed negative surface charge repels it electrostatically, and its hydrated size adds a sieving effect. Rejection of arsenate commonly exceeds 95 percent.
Arsenite, the reduced form (As(III)), is different. At pH below about 9.2 it exists mostly as neutral arsenous acid, which carries no charge for the membrane to repel. Rejection of arsenite is therefore weaker and more variable, often in the 60–90 percent range for a bare membrane. This is the central fact of arsenic removal: oxidation state matters more than membrane brand.
A plain-language version: reverse osmosis is an extremely fine filter that also pushes back on charged particles, and arsenate is charged while arsenite mostly is not.
Quantified context: species, pH, and what membranes actually reject
Arsenate speciation is pH-dependent. Below pH 6.9, the dominant species is singly charged; between roughly 7 and 11, it is doubly charged. The doubly charged form is rejected best, which is why pH near 8 favors arsenate removal. At very high pH (above about 10), silicate and carbonate competition and altered membrane charge can reduce performance.
Arsenite remains neutral until pH climbs past about 9.2. That is above the range of most drinking water, so oxidation is the practical fix. Chlorine, ozone, permanganate, or air with a catalytic media convert arsenite to arsenate before the membrane sees it.
Water chemistry competes for the same rejection pathways. High dissolved solids, hardness, and silica increase osmotic pressure and can depress rejection of trace ions. Temperature matters too: cold water is more viscous, so a system rated at 77°F delivers less permeate and can show changed rejection at 40°F.
The regulatory backdrop explains why this matters. The U.S. maximum contaminant level for arsenic is 10 micrograms per liter (µg/L), set in 2001 and effective in 2006; it replaced an older 50 µg/L standard. The World Health Organization guideline is also 10 µg/L, with a provisional note that it is a practical quantification limit rather than a health-based threshold, since risks persist below it (WHO, Guidelines for Drinking-water Quality).
Process stages where arsenic is won or lost
A whole-house or point-of-use reverse osmosis system is a train, not a single element. Each stage can decide the outcome.
Sediment prefiltration removes particles that would foul the membrane; a fouled membrane loses rejection before it loses flow. Carbon prefiltration removes chlorine, which protects thin-film composite membranes from oxidation, and can also reduce some organic arsenic species. Oxidation or catalytic media (for example, a manganese-based media) converts arsenite to arsenate when source water is anoxic or reducing. The reverse osmosis membrane does the bulk rejection, with a permeate-to-concentrate ratio typically around 1:1 to 1:3 for home systems. Post-carbon polishing addresses taste; it does not remove arsenic and can, in rare cases, leach if not flushed. Storage and distribution lines must be arsenic-free; the treated water is only as clean as what it touches.
The counterintuitive detail: the concentrate stream is not a minor byproduct. A home system rejecting 95 percent of arsenic at 25 percent recovery sends roughly 95 percent of the arsenic into a waste stream that is about four times more concentrated than the feed. If that concentrate is discharged to a drain that feeds a private well or a garden, the arsenic does not disappear; it relocates.
Comparison of arsenic-removal options
| Technology | Arsenate removal | Arsenite removal | Notes |
|---|---|---|---|
| Reverse osmosis | High (about 95–99 percent) | Moderate unless oxidized | Needs pressure; produces concentrate |
| Anion exchange | High | Low to moderate | Regeneration brine carries arsenic |
| Activated alumina | High | Moderate | pH-sensitive; media replacement |
| Iron-based adsorptive media | High | Moderate to high | Media exhausted and replaced |
| Distillation | High | High | Energy-intensive; scaling |
| Boiling | None (concentrates) | None | Increases arsenic concentration |
The table's message: reverse osmosis is the strongest general-purpose option, but only when paired with oxidation for arsenite. Adsorptive and exchange media can match it for arsenate but shift the burden to media disposal.
The maintenance timeline that decides performance
Rejection is not a fixed property. It drifts with membrane condition, and the drift is predictable.
| Time since install | Typical change | What it means for arsenic |
|---|---|---|
| Day 1 | Initial flux high; rejection stabilizing | Flush first permeate; do not sample yet |
| 1–3 months | Prefilters load with sediment and chlorine demand | Rejection can dip if carbon is exhausted |
| 6–12 months | Sediment and carbon cartridges due | Replace on schedule, not on taste |
| 1–3 years | Membrane performance declines with fouling | Test permeate; rejection may fall below target |
| 2–5 years | Membrane replacement window for many home units | Confirm rejection with a lab test |
| Beyond 5 years | Seals, O-rings, and housings degrade | Leakage can bypass the membrane |
The implication: a passing test on installation day says little about year three. Arsenic rejection should be verified with a laboratory test of the permeate, not inferred from flow or taste.
Misconceptions and edge cases
The most common error is assuming all reverse osmosis systems remove arsenic equally. They do not, because arsenite passes more readily. If a home's water is anoxic, from a deep well with iron and manganese, arsenic is likely present as arsenite and a bare membrane will underperform.
A second error is treating boiling as a purification step. Boiling removes water, not arsenic; it concentrates the contaminant. The same logic applies to any process that only removes water.
A third error concerns point-of-use versus whole-house design. Under-sink systems treat drinking and cooking water, which is the exposure pathway that matters most. Whole-house systems treat everything, including water used for irrigation, and their larger membranes and higher flows change the concentrate economics.
Edge cases deserve attention. Water with very high silica or hardness fouls membranes quickly and can lose rejection. Water with high sulfate competes with arsenate for exchange sites on some media but is less of an issue for reverse osmosis. Private wells are not covered by the 10 µg/L federal standard, so testing is the only way to know.
A professional caveat: certified systems are certified as a package. Mixing a certified membrane with uncertified prefilters or a bypass valve voids the performance claim. Certification under NSF/ANSI 58 covers reverse osmosis systems and includes arsenic reduction claims only when the system is tested for that contaminant.
Warning signs that a system is not protecting you:
No arsenic-specific reduction claim on the certification label. No oxidation step where source water is anoxic or high in iron and manganese. Prefilters more than a year old, or a membrane with unknown service life. Permeate flow that has dropped sharply without a corresponding rejection test. Concentrate discharged where it can re-enter the water supply or a garden. A single installation-day test presented as ongoing proof of performance.
Practical actions and thresholds
Start with a laboratory arsenic test that reports species or at least total arsenic, plus iron, manganese, hardness, silica, and pH. Species and pH decide whether oxidation is needed before the membrane.
Compare results to the 10 µg/L federal maximum contaminant level and to the WHO guideline of the same value. Treat the 10 µg/L line as a regulatory floor, not a health guarantee; some authorities note that risk persists below it.
Choose a system certified to NSF/ANSI 58 with an explicit arsenic reduction claim. Confirm the claim covers both arsenate and arsenite, or add a pretreatment oxidation stage. Size the system for the home's daily drinking and cooking volume, not for peak flow.
Set a maintenance schedule: replace sediment and carbon prefilters every 6 to 12 months, test permeate arsenic annually, and plan membrane replacement within the manufacturer's stated life, commonly 2 to 5 years for home units. Test again whenever flow or taste changes.
Manage the concentrate deliberately. Route it to a drain that does not feed a well, cistern, or edible garden. If a private well serves the home, retest the well annually, because a treatment system does not fix the source.
Where arsenic exceeds 10 µg/L and a single under-sink unit is impractical, consider a point-of-entry system or a community solution. For very high levels, blending with a low-arsenic source can be cheaper than treatment.
What reverse osmosis cannot promise
Reverse osmosis is a barrier, not a guarantee. It cannot compensate for a missing oxidation step, a fouled membrane, or a bypass. It does not remove all contaminants equally; neutral small molecules and some dissolved gases pass more freely than charged ions. It produces a concentrate stream that must go somewhere safe. And its performance is only as good as its verification, which means laboratory testing of the permeate rather than trust in the label.
The honest framing: reverse osmosis reliably removes arsenate and, with oxidation, arsenite, at rates that meet the 10 µg/L standard in most residential settings. The variables that decide success are species, pH, pretreatment, maintenance, and disposal, not the word "reverse osmosis" on the box.