Gel electrophoresis separates DNA, RNA, and proteins by driving them through a porous gel with an electric field; smaller and more negatively charged molecules travel farther in a set time. A standard agarose gel at 5 to 10 volts per centimeter resolves DNA fragments from roughly 100 base pairs to 20 kilobases, and the distance each band moves is proportional to the log of its molecular weight. That single principle underpins forensic DNA profiling, clinical genetics, and nearly every molecular biology lab.

How the electric field and gel matrix separate molecules

DNA carries a net negative charge because every nucleotide contributes a phosphate group. When you place the gel in a buffer and apply voltage, the cathode at the loading end repels DNA toward the anode. The driving force on each molecule is proportional to its charge, so in free solution all DNA fragments would accelerate together regardless of length. The gel defeats that. Agarose and polyacrylamide form a mesh of fibers and pores, and a molecule must thread through those pores to advance, so the gel acts as a molecular sieve.

The physics comes down to a trade-off between electric force and frictional drag. A long fragment feels more total charge, hence more force, but it also collides with more of the matrix and drags more buffer with it. For DNA, these effects nearly cancel, leaving mobility that depends mainly on size rather than charge. That is why the technique reports length, not sequence. The relationship between distance migrated and fragment size is approximately linear only when you plot distance against the logarithm of base pairs, which is the single most useful fact for reading a gel.

Agarose gels handle fragments from about 100 base pairs to 20 kilobases. Polyacrylamide gels have smaller pores and resolve fragments in the 1 to 1,000 base pair range, including single-base differences under denaturing conditions. Pulsed-field gels, which alternate the field direction, extend the upper limit into the megabase range, the scale of intact bacterial chromosomes.

Voltage, time, and resolution in numbers

Voltage gradient, not total voltage, controls speed. Most agarose protocols run at 5 to 10 volts per centimeter measured between electrodes, so a 10-centimeter gel at 100 volts sits at the low end. Pushing to 15 volts per centimeter or more accelerates migration but heats the buffer and smears bands, because heat increases diffusion and can distort the gel itself. A typical analytical run takes 30 to 60 minutes.

Resolution depends on gel concentration as much as voltage. A 0.8 percent agarose gel resolves fragments in the 0.5 to 10 kilobase range well. A 2 percent gel tightens resolution below 500 base pairs. For separating fragments that differ by a few percent in length, you raise agarose concentration and lower voltage to give the smaller fragment more time to outrun its neighbor. Running too long lets small fragments run off the gel entirely, a common and unrecoverable error.

Gel type Typical pore scale Best size range Common use
0.6–0.8% agarose Large 1–20 kb Genomic digests, plasmid checks
1–2% agarose Medium 100 bp–1 kb PCR products, cloning verification
4–20% polyacrylamide Small 1–1,000 bp Sequencing, single-base resolution
Denaturing polyacrylamide Small Short single strands Sequencing, fragment analysis
Pulsed-field agarose Variable Up to megabases Intact chromosomes, large fragments

When bands mislead: edge cases and artifacts

Bands are not always what they seem. Supercoiled plasmid DNA migrates faster than its linear form of the same length, so a single plasmid can produce two or three bands. Single-stranded DNA can fold into secondary structures that change mobility unpredictably. Gel loading dye front and ethidium bromide staining both affect how faint smears read as bands.

Counterintuitive detail: a larger fragment can sometimes outrun a smaller one when the smaller molecule is highly supercoiled or when the gel is overloaded and the bands run into each other. Overloading DNA, above roughly 50 nanograms per band for ethidium-stained agarose, causes the trailing edge of a band to collapse and flattens resolution. The practical lesson is that band position alone never proves identity; a size standard and a second method should agree.

Loading too much DNA compresses bands and hides small fragments. Running at excessive voltage smears bands and distorts the dye front. Using the wrong gel percentage puts your target outside the resolvable window. Forgetting the size ladder makes every measurement uninterpretable. Reusing buffer many times changes conductivity and migration speed. Skipping a no-template control lets contamination masquerade as a real band.

Misconceptions about what a gel proves

The most persistent error is treating a band at the expected size as proof of identity. A gel measures size and rough quantity; it does not sequence the fragment, confirm the protein, or exclude a different molecule of similar length. Two different PCR products of the same length produce identical bands. Confirmatory work, whether sequencing or a labeled probe, is what establishes identity.

A second misconception is that a gel quantifies concentration precisely. Ethidium bromide and similar stains bind DNA in proportion to mass, so a band's brightness estimates amount, not molarity. Comparing a 1,000 base pair band to a 100 base pair band at equal brightness means the larger fragment carries about ten times the mass per molecule. A third error is assuming charge drives separation directly. As noted, DNA mobility is nearly independent of charge, which is why the log-size relationship holds. A fourth is assuming proteins behave the same way; native protein gels separate by charge-to-mass ratio and shape, and SDS-PAGE deliberately coats proteins with negative charge so that size dominates, a different design with its own caveats.

Practical steps that produce interpretable gels

Start by defining the size window, then pick gel concentration and voltage to match. For a PCR product expected near 500 base pairs, a 1.5 percent agarose gel at 7 volts per centimeter for 45 minutes usually suffices. Always load a size ladder spanning your target, and load the same ladder in the same buffer batch.

Prepare the gel with the correct buffer dilution, since a 10x stock mixed incorrectly changes ionic strength and migration. Load 5 to 20 microliters of sample containing roughly 10 to 50 nanograms of DNA per band. Let the gel solidify fully, because a partially set gel has uneven pores. Run until the tracking dye reaches about 80 percent of the gel length, then image promptly so diffusion does not blur your record.

A reasonable decision threshold: if your target band and the nearest ladder band differ by less than the gel can resolve at that percentage, rerun at higher concentration or lower voltage rather than trusting the first image. If a band appears at an unexpected size, treat it as a possible artifact or contaminant before accepting it as a result.

Where the method stops

Gel electrophoresis cannot read sequence, cannot distinguish molecules of identical size, and cannot reliably quantify without a calibrated standard. Its resolution has a hard floor set by pore size and diffusion. Proteins require a different preparation, and any diagnostic use demands validated controls and regulatory clearance specific to the assay. The technique remains indispensable precisely because it is simple, cheap, and fast, but its output is a size estimate that must be interpreted with the limits of the method in view.